Ecohome Easter - Sale Banner 2024

Order Before 2pm For Delivery on

Free Next Day Delivery

FREE NEXT WORKING DAY DELIVERY

Orders £100+VAT. Excludes Bank Holidays.

Free Next Day DeliveryFree Next Working Day Delivery

Free Next Day DeliveryBeat The Energy Price Hike

How To Insulate Your Timber Building Using an EcoPro Shed Insulation Kit

Difficulty: Easy • 10 Steps

In this helpful guide, you will find out how to easily Insulate the walls and roof of any timber buildings using the EcoPro Shed Insulation Kit. In the kit you will receive EcoQuilt Expert, ThermaSeal Foil Joining Tape, a Heavy Duty Staple Gun Kit (consists of Staple Gun & 14mm Staples) and a Cutting Knife.

EcoQuilt Expert is a Highly Reflective 6 Layer Multifoil Insulation Blanket, designed to keep you warmer in the winter and cooler in the summer. It has a built in High Performing Vapour Control Layer which effectively stops any form of damp rising into your room. EcoQuilt Expert is 15mm at a relaxed thickness and compresses to approximately 5mm.

Let’s start with the roof, then move onto the walls..

Ecohome-Insulation are the leading UK & European distributor of Multifoil Insulation products. We offer free next working day delivery to the UK Mainland (On Orders placed before 2pm – Orders over £100 + VAT)

Method Steps

  1. Staple the EcoQuilt Expert under the roof rafters

    Start by stapling EcoQuilt Expert to the roof rafters using the Heavy Duty Staple Gun Kit. Ensure that the material is pulled taut across onto the next rafter. Then, Staple down the second rafter at a maximum of 2 inches apart.

  2. Secure & Cut off any excess

    Once you have secured the first section, cut any excess material off with the sharp blade provided in the EcoPro Shed Insulation Kit.

  3. Repeat the process

    Install the next section in the exact same way, stapling to the rafters and cutting off any excess. Remember to ensure a 50mm overlap of material.

  4. Seal with ThermaSeal Foil Joining Tape

    Once you’ve stapled your EcoQuilt, it’s now time to seal all of the joints and edges with ThermaSeal Foil Joining Tape. This is what creates the Vapour Control barrier.

  5. Fixing your roof counter battens

    Now you can fix the 19mm battens to secure your EcoQuilt, using screws with a minimum length of 35mm. Fix the remaining battens in the exact same way. Now, you are ready to install the surface finish of your choice.

  6. It’s time to insulate the walls

    For buildings with existing studwork, hold your insulation into place and simply recess the EcoQuilt halfway back by stapling it onto the side of the stud. Ensure a 19mm air gap either side of the insulation. Then continue by pulling the material taut before securing onto the next timber stud. Ensure EcoQuilt is stapled at minimum intervals of 300mm, using the 14mm staples provided.

  7. Attaching battens (if needed)

    If your space does not have timber uprights, you can fit 19mm battens onto the walls using screws.

  8. Seal the with ThermaSeal Foil Joining Tape

    Now that all of your EcoQuilt is stapled into position, it’s time to seal all overlapping joints and around the perimeter with ThermaSeal Foil Joining Tape to ensure an airtight seal.

  9. Fixing your wall Counter battens

    As you did with the roof, fix the 19mm battens to secure your EcoQuilt using screws with a minimum length of 35mm. Fix the battens, in the same place as the existing wall studs. Repeat the exact same process. Now you’re ready to install the final surface finish of your choice and decorate!

  10. Enjoy your fully insulated Timber building!

Buy Tools & Materials

Disclaimer – Ecohome Insulation cannot be held responsible for any losses financially or physically from advice provided in this How-To-Guide.

Recommended fixing materials and good building practice should also be used.

trending_flatBack to All Guides
Ecohome-Insulation.co.uk Logo